lattice ball mill

Lattice Ball Mill

The lattice ball mill is the key equipment for crushing the material after it is crushed. The effect of fine grinding is better than that of coarse grinding. When fine grinding, the general feeding size should not exceed 65 mm, and the most suitable feeding size is below 6 mm.

⌈ Production capacity ⌋:1.4-50 t/h

⌈ Motor power ⌋:45-1000 kw

⌈ Application range ⌋:Lattice ball mills are used to grind various ores and other materials and are widely used in mineral processing, construction and chemical industries.

⌈ Applicable material ⌋:Slag, calcite, marble, dolomite, limestone and other materials.

international trade: 0086-371-66888887

Outstanding advantages

  • Conical design at the discharge end for high product accuracy

    The discharge end of the lattice ball mill adopts a cone design, which increases the volume and forces the steel ball at the cone end to be graded. The closer to the outlet, the smaller the diameter of the steel ball increases the effect of repeated grinding, and the fineness of the material further improve.

  • Rolling instead of sliding, efficient and low-cost

    The ball mill drive adopts rolling bearing instead of sliding bearing, the friction force is greatly reduced, the starting is easy and energy saving is remarkable; the power consumption can be reduced to 25-35%, which greatly reduces the production cost for the customer.

  • Reasonable structural design and stable operation

    The structure of the lattice ball mill is rationalized, the equipment is stable in operation, the amplitude is small, the failure rate is low, the operation rate is high, and the production volume is greatly improved, so that the lattice type ball mill plays a dominant position in the same regulation equipment.

Equipment composition

The lattice ball mill has a hollow journal end cap at the discharge end, and is provided with a bearing inner sleeve and a discharge grid. The drainage grid consists of a central lining, a lattice lining and a lining. Eight radial ribs are cast on the inner wall of the end cover, the end cover is divided into eight fan-shaped chambers, a 衬-shaped lining is installed in each sector, and is fixed on the end cover by screws, and then the grid plate is mounted on A lining plate is formed on each of the sector chambers.

 

Working principle

The lattice ball mill is a horizontal cylindrical rotating device, with external gear transmission and two bins. The material is uniformly fed into the first chamber of the mill by the feeding device through the hollow shaft of the feeding material. The chamber has stepped lining or corrugated lining, which is filled with steel balls of different specifications. The rotation of the cylinder generates centrifugal force to bring the steel ball to a certain height and then falls, which causes heavy impact and grinding on the material. After the material reaches the rough grinding in the first warehouse, it enters the second warehouse through the single-layer compartment board. The warehouse is provided with a flat lining plate with steel balls inside to further grind the material. The powder is discharged through the discharge raft to complete the grinding operation.

The milled product of the lattice ball mill is discharged by the drainage grid plate, which has the effect of forced ore discharge, and the discharge rate is fast. The level of the slurry surface at the discharge end is lower than the lowest level of the discharge shaft, so it is called horizontal discharge. In the mill from the feed end to the discharge end of the slurry surface, the speed of the slurry passing through the mill is accelerated, so that the finely ground ore can be discharged in time.

Technical Parameters

Model Specification(mm) Capacity(t/h) Rotational speed(r/min) Balls weight(t) Power(kw) Weight(t)
MQG1245 1200×4500 1.4-2 35 5.2 45 12
MQG1557 1500×5700 3.5-4.5 29 12.25 115 23
MQG1864 1830×6400 5.5-6.4 24.23 18.5 155 34.6
MQG1870 1830×7000 6—7 23.91 21 185 36.5
MQG2265 2200×6500 14-15 21.4 31 380 50
MQG2275 2200×7500 16-18 19 32.5 380 63
MQG2470 2400×7000 26-30 17 38 475 70.5
MQG3090 3000×9000 42-50 15 65 1000 156.5

Note: the production capacity of different materials is different, please consult for more details: 0086-371-66888887

Product display

We promise

1. Pre-sales service, actively provide technical data support for customers, free to provide program design and investment quotation estimates.

2. Provide customers with tailor-made global transportation arrangements to ensure safe and fast delivery of goods.

3. Regularly return visits to all users to track product usage, ensure that equipment is in optimal working order, and help customers achieve maximum benefits.

Related devices

  • energy-saving ball mill

    Energy-Saving Ball Mill

  • dry ball mill

    Dry Ball Mill

  • Raymond mill

    Raymond Mill

  • rod mill

    Rod Mill

  • cement ball mill

    Cement Ball Mill

Contact us

International Trade Department

  • TEL:0086-371-66888887
  • Email:sales@bljq.com
  • WhatsApp:+86-18203639337
  • You can also leave your contact information and product requirements in the form below, our engineers will contact you as soon as possible!
Return to the top

All copyright © BAILING MACHINERY Service hotline:0086-371-66888887 / 18203639337 Links:ball mill ball mill machine rotary dryer rotary kiln